We're sorry, but eCampus.com doesn't work properly without JavaScript.
Either your device does not support JavaScript or you do not have JavaScript enabled.
How to enable JavaScript in your browser.
Need help? Call 1-855-252-4222
A Signal Integrity Engineer’s Companion
Real-Time Test and Measurement and Design Simulation
Geoff Lawday
David Ireland
Greg Edlund
Foreword by Chris Edwards, Editor, IET Electronics Systems and Software magazine
Prentice Hall Modern Semiconductor Design Series
Prentice Hall Signal Integrity Library
Use Real-World Test and Measurement Techniques to Systematically Eliminate Signal Integrity Problems
This is the industry’s most comprehensive, authoritative, and practical guide to modern Signal Integrity (SI) test and measurement for high-speed digital designs. Three of the field’s leading experts guide you through systematically detecting, observing, analyzing, and rectifying both modern logic signal defects and embedded system malfunctions. The authors cover the entire life cycle of embedded system design from specification and simulation onward, illuminating key techniques and concepts with easy-to-understand illustrations.
Writing for all electrical engineers, signal integrity engineers, and chip designers, the authors show how to use real-time test and measurement to address today’s increasingly difficult interoperability and compliance requirements. They also present detailed, start-to-finish case studies that walk you through commonly encountered design challenges, including ensuring that interfaces consistently operate with positive timing margins without incurring excessive cost; calculating total jitter budgets; and managing complex tradeoffs in high-speed serial interface design.
Coverage includes
About the Authors: Dr. Geoff Lawday is Tektronix Professor in Measurement at Buckinghamshire New University, England. He delivers courses in signal integrity engineering and high performance bus systems at the University Tektronix laboratory, and presents signal integrity seminars throughout Europe on behalf of Tektronix. David Ireland, European and Asian design and manufacturing marketing manager for Tektronix, has more than 30 years of experience in test and measurement. He writes regularly on signal integrity for leading technical journals. Greg Edlund, Senior Engineer, IBM Global Engineering Solutions division, has participated in development and testing for ten high-performance computing platforms. He authored Timing Analysis and Simulation for Signal Integrity Engineers (Prentice Hall).
Dr. Geoffrey Lawday currently holds the Tektronix Chair in Measurement at Buckinghamshire New University where he teaches embedded system design and high performance computing in the School of Computing. Having gained a BSc in Physics and an MSc in Computer Engineering at Surrey University, he was awarded a PhD in Time-Frequency Signal Analysis from Brunel University. His research in signal integrity engineering is reflected in his publications, such as the critique on the introduction of the new serial buses published in the flagship journal of the Institution of Electrical Engineers.
David Ireland has more than thirty years experience in test and measurement ranging from an engineering apprenticeship with Racal, where he gained his formal electronic engineering qualifications, to his current position at Tektronix, where he is the marketing manager of design and manufacturing at Tektronix Europe. He is widely recognized by embedded system engineers in Europe for his signal integrity articles and collaborative workshops on high-speed digital system design, test, and measurement.
Greg Edlund’s career in signal integrity began in 1988 at Supercomputer Systems, Inc., where he simulated and measured timing characteristics of bipolar embedded RAMs used in the computer’s vector registers. Since then, he has participated in the development and testing of nine other high-performance computing platforms for Cray Research, Inc., Digital Equipment Corp., and IBM Corp. He has had the good fortune of learning from many talented engineers while focusing his attention on modeling, simulation, and measurement of IO circuits and interconnect components. A solid physical foundation and practical engineering experience combine to form a valuable perspective on optimizing performance, reliability, and cost.
Foreword xv
Preface xix
Acknowledgments xxviii
About the Authors xxx
1 Introduction: An Engineer’s Companion 1
2 Chip-to-Chip Timing and Simulation 31
3 Signal Path Analysis as an Aid to Signal Integrity 87
4 DDR2 Case Study 117
5 Real-Time Measurements: Probing 159
6 Testing and Debugging: Oscilloscopes and Logic Analyzers 213
7 Replicating Real-World Signals with Signal Sources 255
8 Signal Analysis and Compliance 287
9 PCI Express Case Study 367
10 The Wireless Signal 399
Index 439
The New copy of this book will include any supplemental materials advertised. Please check the title of the book to determine if it should include any access cards, study guides, lab manuals, CDs, etc.
The Used, Rental and eBook copies of this book are not guaranteed to include any supplemental materials. Typically, only the book itself is included. This is true even if the title states it includes any access cards, study guides, lab manuals, CDs, etc.